Thin Film (Wiped Film) Evaporator vs Batch Still for Used Oil Re-Refining
Updated: 3 days ago
Every used oil re-refinery has a vacuum distillation step at its heart. It separates the base oil from the metals, additive residues and asphaltic material that stay behind. There are two ways to do it: a batch vacuum still, which heats a charge of oil for hours, and a thin film evaporator (TFE), also called a wiped film evaporator, which spreads the oil over a heated wall and distils it in seconds.
In short, batch stills suit plants up to about 15 TPD and give the lowest entry cost; thin film evaporators run continuously, treat the oil more gently, give sharper base oil cuts and are the usual choice from about 20 TPD. The rest of this article explains why.
Key takeaways
Both methods distil under vacuum, so the base oil boils well below the temperature at which it cracks.
A batch still keeps the oil hot for hours; a thin film evaporator keeps it on the hot wall for only 10 to 90 seconds.
Batch plants make a light and a heavy Group I base oil. Two-stage TFE plants make fractionated SN-150 and SN-500 with VI 95 min, and a third evaporator adds an SN-300 cut.
Batch is simpler, cheaper and tolerant of variable feed. TFE uses less energy and labour per tonne and runs 24 hours a day.
Either way the distillate needs finishing. LINUS plants use RMP regenerative polishing, with no acid and no clay.
Why used oil is distilled under vacuum
The heavy base oil in used engine oil would have to be heated far above 300 °C to boil at atmospheric pressure, and at those temperatures it cracks into lighter, smelly and unstable products. Lowering the pressure lowers the boiling point. Under deep vacuum the base oil vaporises without thermal damage, and the metals, additive residues and asphaltic material stay in the residue.
How a batch vacuum still works
A batch still is a heated vessel with a packed re-refining column, condensers and a vacuum system. The still is charged with pre-treated used oil and heated on a ramp. Water and light ends come off first, then the light fuel, and then, under a vacuum below 10 mbar, the base oil. The column, with reflux, splits a light base oil (SN-150 type) from a heavy base oil (SN-350/500 type). The batch ends at about 320 °C, the asphalt residue is drained and the still is ready for the next charge.
Because the oil stays hot for hours, the end temperature and vacuum are controlled closely to limit cracking. LINUS builds three batch plants: the LP-WOD-5B runs one 5 t batch a day, the LP-WOD-10B one 10 t batch a day in a 12.5 kL still, and the LP-WOD-20B two batches a day from two stills staggered on one thermic fluid heater.

LP-WOD-10B: a 10 TPD batch plant built around a 12.5 kL vacuum still and packed re-refining column.
How a thin film (wiped film) evaporator works
A thin film evaporator is a vertical cylinder with a heated jacket and a rotor inside. Oil enters at the top, and the rotor’s wiper blades spread it into a thin, turbulent film on the hot wall. The base oil evaporates from the film within seconds and is condensed, while the heavier residue runs down the wall and leaves from the bottom. Because the film is thin and constantly renewed, heat transfer is fast and the oil spends only 10 to 90 seconds on the hot wall.
A LINUS continuous plant first removes water and light ends in a packed dehydration column at 110 to 135 °C and 600 to 700 mbar, strips the light fuel, and then uses two evaporators in series. TFE-1, with a wall temperature of 220 to 260 °C at 10 to 30 mbar, takes off the light base oil. TFE-2, at 280 to 320 °C and 0.5 to 3 mbar, takes off the heavy base oil and leaves the asphalt residue. A third evaporator can add an SN-300 cut.
Wiped film, thin film or short path? “Thin film evaporator” and “wiped film evaporator” are two names for the same machine. A short path evaporator is a wiped film evaporator with the condenser built inside, close to the hot wall, which allows a deeper vacuum.

LP-WOD-10C: the smallest LINUS continuous plant, with two thin film evaporators in series.
Batch still and thin film evaporator compared
Batch vacuum still | Thin film (wiped film) evaporator | |
|---|---|---|
Operation | Batch cycles: charge, heat, distil, drain | Continuous, 24 hours a day |
Typical capacity | Up to about 15 TPD (LINUS: 5 to 20 TPD) | From about 20 TPD (LINUS: 10 to 200 TPD) |
Time at high temperature | Hours | 10 to 90 seconds on the hot wall |
Vacuum | Below 10 mbar at the end of the batch | 10 to 30 mbar (TFE-1) and 0.5 to 3 mbar (TFE-2) |
Base oil products | Light (SN-150 type, colour L 2.5 max) and heavy (SN-350/500 type, colour L 3.5 max), Group I | SN-150 (colour L 1.5 max) and SN-500 (colour L 2.5 max), VI 95 min, Group I; SN-300 with a third TFE |
Feed flexibility | Very tolerant of variable feed | Best on steady, well-dehydrated feed |
Energy per tonne | Higher | Lower; the heater burns the plant’s own light fuel |
Manpower | 2 operators and a helper (5 TPD) | A supervisor and 2 to 4 operators per shift (C-series) |
Operating days in our figures | 300 a year | 330 a year |
Entry cost | Lowest | Higher, with a lower cost per tonne at scale |
Upgrade path | Add a second still (twin-still 20 TPD) | Add a third TFE, more polishing or hydrofinishing |
Cracking, colour and smell: why time at temperature matters
Base oil molecules start to crack when they are held at high temperature. Cracking makes light, unstable fractions that darken the oil, give it a burnt smell and lower its flash point and viscosity. A thin film evaporator avoids most of this by keeping the oil on the hot wall for seconds. A batch still controls it with deep vacuum, a packed column and an end temperature of about 320 °C. Either way, the distillate is finished in LINUS RMP regenerative polishing columns at 80 to 100 °C, which remove the remaining colour, odour, organic acids and oxidation products.
Fouling and maintenance
In a batch still, coke and sludge build up on the heated surfaces over time and are cleaned out between campaigns. In a thin film evaporator the wiper blades keep the wall clean as they spread the film, so the main maintenance items are the rotor, its bearings and mechanical seal, and the vacuum system. Both depend on good pre-treatment: removing water, solids and sludge before distillation is what keeps either one running.
Which one should you choose?
Choose batch if you are starting with up to about 15 TPD, your feed varies, you want the simplest operation and the lowest entry cost, and light and heavy Group I base oil suit your buyers.
Choose thin film evaporation if you will process 20 TPD or more, have a steady collection network, sell to blenders who want fractionated SN-150 and SN-500 with tight colour, or plan to grow.
Consider the LP-WOD-10C if you collect about 3,300 tonnes a year and want continuous quality from the start: it is our smallest continuous plant, at 0.42 t/h.
Add hydrofinishing at around 200 TPD if your market pays for Group II base oil.
LINUS batch and continuous plants
LINUS PROJECTS builds both, as prefabricated, pre-wired modules that are factory-tested and ready to install: the B-series batch plants (5, 10 and 20 TPD), the C-series continuous TFE plants (10, 20, 30, 50 and 100 TPD) and the 200 TPD LP-WOD-200H with catalytic hydrofinishing. Typical base oil yield is 68 to 74 % of wet feed, and every plant is finished by RMP polishing.





Comments