top of page
Linus Projects Logo

Base Oil Yield from Used Oil: How to Compare Re-Refinery Yield Claims

3 days ago
4 min read

Updated: 3 days ago

Yield is the first number buyers ask for and the easiest one to misread. Two suppliers can describe the same plant as 71 % and 81 %, and both can be telling the truth, because they are measuring different things. This guide explains what a used oil re-refinery actually recovers from a tonne of used oil, and how to put competing yield claims on the same footing.

Key takeaways

  • A well-run re-refinery recovers 68 to 74 % of wet used oil as base oil. On dry feed the same plant reads 72 to 79 %.

  • Figures that count light fuel with the base oil, or that use dry feed, read higher. Ask for base oil alone, on wet feed of a stated specification.

  • Feed quality moves yield more than anything else: water, fuel dilution, sludge and ash all come off before base oil.

  • Finishing matters too. Acid–clay treatment yields only 50 to 65 %, and clay finishing leaves oil behind in the spent clay.

  • A typical figure describes good feed on a good day. A guaranteed figure, tied to a feed specification, is the one to compare.

What comes out of one tonne of used oil

Used oil is mostly base oil, but it also carries water, fuel, soot, metals and spent additives. A re-refinery splits it into base oil, light fuel, asphalt residue and water. Typical figures for a LINUS continuous plant on specification feed:

Stream

Share of wet feed

What happens to it

Base oil

68 to 74 %

Sold to lubricant blenders as Group I or Group II base oil

Light fuel (diesel range)

6 to 12 %

Fires the plant’s thermic fluid heater; surplus sold

Asphalt residue

9 to 17 %

Sold as a bitumen extender or heavy fuel

Water

3 to 7 %

Treated in the effluent treatment plant

Light ends and handling losses

About 1 %

Sent to tail-gas treatment

About 98 % of the dry feed leaves the plant as saleable product. The question is how much of it is base oil, the product that earns the most.

Wet feed or dry feed?

Used oil arrives with water in it, typically 3 to 7 %. A yield on dry feed divides the base oil by the oil left once the water is removed; a yield on wet feed divides it by everything that arrived in the tanker. The same plant therefore reads higher on dry feed.

Worked example. A plant receives 10 tonnes of used oil containing 5 % water, so 9.5 tonnes of dry feed. It recovers 7.1 tonnes of base oil. That is 75 % of the dry feed but 71 % of the wet feed: one result, two numbers.

Base oil or total oil?

Some figures count every oil product the plant recovers, base oil and light fuel together. In the example, the plant also recovers 1.0 tonne of light fuel, so its total oil recovery is 8.1 tonnes, or 81 % of the wet feed. Only 7.1 tonnes of that is base oil, and light fuel sells at fuel prices. The remaining 1.4 tonnes are asphalt residue and losses.

So “81 % recovery” and “71 % base oil yield” can describe the same plant. Always ask which products a figure includes.

Typical or guaranteed?

A typical yield describes what a plant achieves on good feed. A guaranteed yield is a contractual minimum on feed of an agreed specification. LINUS quotes typical base oil yields of 68 to 74 % of wet feed (72 to 79 % of dry feed) and guarantees 65 % on specification feed, and every plant is handed over after a 72-hour performance test.

LINUS LP-WOD-200H 200 TPD modular used oil refinery with catalytic hydrofinishing for Group II base oil

LP-WOD-200H: two thin film evaporator trains with catalytic hydrofinishing for Group II base oil.

Feed quality sets the ceiling

Everything that is not base oil comes off before base oil does. A load with more water, more fuel dilution or more sludge gives less base oil per tonne, whatever the plant. That is why LINUS performance guarantees apply to feed within agreed limits:

  • Water: 10 % max

  • Light hydrocarbons (fuel dilution): 8 % max

  • Sludge: 3 % max

  • Ash: 1.5 % max

  • Chlorine: 1,000 ppm max

  • PCB: not detectable

Feed outside these limits can still be processed; yields are then confirmed on a sample analysis. PCB-containing oils, chlorinated solvents, brake fluid, glycols, bulk vegetable oils and emulsions are rejected at the gate.

How the finishing step changes yield

The finishing step decides how much distilled oil ends up as saleable base oil, and what waste the plant leaves behind:

Finishing route

Base oil yield (dry feed)

What it leaves behind

Acid–clay treatment

50 to 65 %

Acid sludge and oily clay; banned in many countries

Vacuum distillation + clay

65 to 72 %

Oily spent clay, 4 to 7 % of the base oil

Solvent extraction

65 to 70 %

Extract to dispose of; solvent recovery

Batch still + LINUS RMP polishing

72 to 77 %

No acid sludge or spent clay; asphalt residue is sold

Thin film evaporation + LINUS RMP polishing

72 to 79 %

No acid sludge or spent clay

Thin film evaporation + hydrofinishing + RMP

74 to 79 %

Spent catalyst every 3 to 4 years

Acid treatment and clay both take oil away with the contaminants. Regenerative polishing removes colour, odour and acids in adsorbent columns that regenerate in place, so no oily clay leaves the plant.

Questions to ask any supplier

  1. Is the figure base oil alone, or base oil plus light fuel?

  2. Is it on wet feed or dry feed, and for what water content?

  3. What feed specification does it assume for water, fuel dilution, sludge, ash and chlorine?

  4. Is it typical or guaranteed, and how is the guarantee demonstrated?

  5. What finishing route does it assume, and how much clay, acid or other consumable goes with it?

  6. What grade and colour is the base oil at that yield?

Get a yield estimate for your own oil

Send us an analysis of the used oil you collect, or a sample, with your monthly volume. We will tell you the base oil yield to expect on wet and dry feed, the grades you can make and the LP-WOD model that fits.

Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
bottom of page

Unit 1 (Registered Office): Plot No. N-86/3, Bohonoli Village, Anand Nagar Additional MIDC, opp. CEAT Tyres, Ambernath (East), Maharashtra 421506, India

Unit 2 (Manufacturing Unit): Plot No. B-73/1, Jhambivali Village, Additional Ambernath MIDC, Ambernath (East), Maharashtra 421506, India