top of page
Linus Projects Logo

How to Start a Used Oil Re-Refining Business in India

3 days ago
7 min read

Updated: 3 days ago

India’s lubricant market produces a large and steady stream of used oil, and since 1 April 2024 the law has given that oil a new value. Under the extended producer responsibility (EPR) rules for used oil, producers and importers of base oil and lubricants must meet rising recycling targets, and they can meet them only by buying EPR certificates from registered recyclers. A re-refinery therefore earns twice from the same litre: once from the base oil, light fuel and asphalt it sells, and once from the certificates.

This guide sets out the steps in the order that matters, from securing feed to running the plant.

Key takeaways

  • Start with collection, not with the plant. Size the plant on the used oil you can reliably collect within 300 to 500 km; a 10 TPD continuous plant needs about 3,300 tonnes a year.

  • Decide what you will sell before you choose technology: Group I base oil cuts for blenders, Group II base oil at large scale, plus light fuel, asphalt residue and EPR certificates.

  • You need State Pollution Control Board consent to establish and to operate, hazardous waste authorisation and registration as a used oil recycler on the CPCB EPR portal.

  • Producer EPR targets rise from 5 % in 2024-25 to 40 % in 2028-29 and 50 % from 2030-31, so demand for certificates grows year by year.

  • A modular plant is built in the factory while your civil works proceed. LINUS hands over 5 to 100 TPD plants 26 to 46 weeks from order.

Step 1: Secure your used oil supply

Used oil comes from vehicle workshops and dealerships, fleet and transport operators, factories, mines, ports, railways and power plants. Bulk generators of more than 100 tonnes a year must hand their used oil only to registered recyclers, producers or registered collection agents, so the first job is to build those relationships.

CPCB guidelines for collection agents, effective 1 April 2024, set up two levels:

  • Level-1 agents collect and transport used oil without storage, typically within 75 to 150 km of a recycler or a Level-2 agent. They register on the portal themselves, subject to validation by the State Pollution Control Board.

  • Level-2 agents collect, store and transport used oil over a wider area, and need consent to establish and operate and hazardous waste authorisation before they register.

Collected used oil can be stored for up to 90 days, in separate tanks for different types of oil. A re-refiner can run its own collection or sign agreements with registered agents near it.

Size the plant on the oil you can collect, with a margin. A 5 TPD batch plant needs about 1,500 tonnes a year, a 10 TPD continuous plant about 3,300 tonnes and a 50 TPD plant about 16,500 tonnes. The table in step 3 gives every size.

Step 2: Decide what you will sell

  • Base oil is the main product, 68 to 74 % of wet feed. Batch plants make a light (SN-150 type) and a heavy (SN-350/500 type) Group I base oil; continuous thin film plants make SN-150 and SN-500 with VI 95 min; the 200 TPD hydrofinishing plant makes Group II 70N to 500N.

  • Light fuel, 6 to 12 % of feed, fires the plant’s thermic fluid heater, and the surplus is sold.

  • Asphalt residue, 9 to 17 % of feed, is sold as a bitumen extender or heavy fuel.

  • EPR certificates are generated on the CPCB portal for the end product you recover.

Talk to lubricant blenders before you size the plant. The grades and colour they buy decide between batch and continuous technology, and whether a third evaporator for an SN-300 cut, or hydrofinishing for Group II, is worth adding.

Step 3: Choose capacity and technology

Batch vacuum distillation suits plants up to about 15 TPD: the lowest entry cost, simple operation and tolerance of variable feed. Continuous two-stage thin film evaporation is the usual choice from about 20 TPD and gives fractionated cuts with lower energy and labour per tonne. Above 100 TPD, hydrofinishing makes Group II base oil. Our comparison of thin film evaporators and batch stills explains the trade-offs.

Model

Plant

Used oil per year

Base oil per year

Plot about

LP-WOD-5B

5 TPD batch

1,500 t

1,060 t

600 m²

LP-WOD-10B

10 TPD batch

3,000 t

2,115 t

900 m²

LP-WOD-20B

20 TPD batch, twin still

6,000 t

4,230 t

1,500 m²

LP-WOD-10C

10 TPD continuous

3,300 t

2,340 t

1,400 m²

LP-WOD-20C

20 TPD continuous

6,600 t

4,690 t

2,200 m²

LP-WOD-30C

30 TPD continuous

9,900 t

7,030 t

3,000 m²

LP-WOD-50C

50 TPD continuous

16,500 t

11,700 t

4,800 m²

LP-WOD-100C

100 TPD continuous

33,000 t

23,400 t

8,000 m²

LP-WOD-200H

200 TPD continuous with hydrofinishing

66,000 t

47,500 t

16,000 m²

Used oil per year at 300 operating days for batch plants and 330 for continuous plants. Allow roughly twice the plant plot for tanker parking, a weighbridge, office, fire water, green belt and expansion.

Step 4: Choose the site

Look for a plot in a notified industrial area, such as an MIDC or GIDC estate, with tanker access, a reliable power supply and water. Plan for more than the process plant: tankage for raw used oil and finished products, a laboratory, an effluent treatment plant for the separated water, a utility area and room to expand. LINUS plot plans start at about 600 m² for 5 TPD and reach about 16,000 m² for 200 TPD.

LINUS LP-WOD-100C 100 TPD modular continuous used oil re-refining plant with bunded tank farm

Site layout of a 50 TPD continuous re-refinery: process structure, tank farm and heater stack.

Step 5: Get the permits

Used oil is a hazardous waste under the Hazardous and Other Wastes (Management and Transboundary Movement) Rules, 2016. A re-refinery typically needs:

  • Consent to Establish from the State Pollution Control Board under the Water and Air Acts, before construction starts.

  • Consent to Operate and hazardous waste authorisation from the State Pollution Control Board, before the plant runs.

  • Registration as a used oil recycler on the CPCB EPR portal, which is what allows EPR certificates to be generated.

  • Factory licence and fire safety approval, and a PESO licence under the Petroleum Rules, 2002 if you store the light fuel above the licence-free limits.

  • GST and the usual business registrations.

Requirements vary from state to state, so confirm the full list with your State Pollution Control Board before you finalise the site. For each project LINUS prepares the documents these applications ask for: process description, PFD and P&IDs with mass and energy balance, plot plan with tank farm, bund and fire-water layout, and effluent, emission and hazardous waste management notes.

Step 6: Order, build and commission the plant

A modular plant shortens this step. LINUS builds every LP-WOD plant as prefabricated, pre-wired skid modules at its Ambernath works while your civil works and permits proceed. Modules are hydro-tested, loop-checked and factory acceptance tested, then shipped numbered with match-marked spools. At site they are set on foundations, bolted together and hooked up.

Compact modular used oil re-refining plant: receiver, vacuum pump skid and process structure on concrete plinths

Ready-to-install LP-WOD modules are set on foundations and bolted together at site.

From order to hand-over takes 26 to 46 weeks for the 5 to 100 TPD plants, and about 100 weeks for the 200 TPD hydrofinishing plant. Commissioning ends with a 72-hour performance test, and operators are trained at site and at our works.

Step 7: Run the plant and earn EPR certificates

Once registered, the plant records the used oil it receives and the products it recovers on the CPCB portal, and the portal generates EPR certificates. The certificate quantity is the end product recovered, multiplied by a conversion factor that CPCB sets for the technology and by a weightage for the end product: 1.0 for re-refined base oil or lubricating oil, 0.25 for co-processing or energy recovery. Certificates are valid for two years from the end of the financial year in which they are issued, and producers buy them to meet their targets. See the CPCB used oil FAQ.

Producer targets, as a share of the base oil or lubricating oil they sold or imported two years earlier: 5 % in 2024-25, 10 % in 2025-26, 20 % in 2026-27 and 2027-28, 40 % in 2028-29 and 2029-30, and 50 % from 2030-31.

What drives profitability

  • The spread between feed cost and base oil price. It decides most of the margin, so lock in collection before you lock in capacity.

  • Utilisation. Plant output figures assume 300 operating days a year for batch plants and 330 for continuous plants; every idle day costs margin.

  • Feed quality. Water, fuel dilution and sludge reduce the base oil yield. LINUS guarantees performance on feed within agreed limits: water 10 %, light hydrocarbons 8 %, sludge 3 %, ash 1.5 % and chlorine 1,000 ppm, with no detectable PCB.

  • Energy. Continuous plants fire their heater on their own light fuel and buy no fuel after start-up.

  • Finishing cost. RMP polishing typically costs USD 8 to 15 per tonne of base oil, with no clay or acid to buy or dispose of.

  • Manpower. From 2 operators and a helper on the 5 TPD batch plant to a supervisor and 2 to 4 operators per shift on the C-series continuous plants.

  • EPR certificate sales to producers, which add revenue to every tonne of base oil recovered.

Mistakes to avoid

  • Buying a plant for the oil you hope to collect rather than the oil you have agreements for.

  • Choosing acid–clay treatment because it is cheap to buy: it leaves acid sludge and oily clay, and it is banned in many countries.

  • Skipping incoming tests: oil containing PCB, chlorinated solvents, brake fluid or glycols must be rejected at the gate.

  • Undersizing storage and the laboratory, which keep the plant running steadily.

  • Forgetting the by-products: line up buyers for asphalt residue and surplus light fuel from day one.

Talk to us about your project

LINUS PROJECTS (INDIA) designs and manufactures modular used oil re-refining plants from 5 to 200 TPD at Ambernath MIDC near Mumbai, and has supplied 240+ plants and machines to 48+ clients in India, Africa, the Middle East and Asia since 2014. Send us your collection volume, the oils you collect, your location and the grades your market buys, and we will recommend a model with a plot plan and a techno-commercial offer.

Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
bottom of page

Unit 1 (Registered Office): Plot No. N-86/3, Bohonoli Village, Anand Nagar Additional MIDC, opp. CEAT Tyres, Ambernath (East), Maharashtra 421506, India

Unit 2 (Manufacturing Unit): Plot No. B-73/1, Jhambivali Village, Additional Ambernath MIDC, Ambernath (East), Maharashtra 421506, India