How Used Engine Oil Is Re-Refined into Base Oil: A Step-by-Step Guide
Updated: 3 days ago
Used engine oil is not worn out. The base oil that makes up most of every litre barely changes in service; what turns it into waste is the water, fuel, soot, metals and spent additives it collects. A used oil refinery, also called a used oil re-refining plant, removes those contaminants and recovers the base oil so it can be blended into new lubricants again.
This guide walks through each stage of used engine oil re-refining, what comes out of the plant, how to choose between batch and continuous technology, and the permits a re-refinery needs in India.
Key takeaways
A modern re-refinery recovers 68 to 74 % of wet used oil (72 to 79 % of dry feed) as base oil. Light fuel, asphalt residue and water make up the rest, and about 98 % of the dry feed is sold as product.
The heart of the process is vacuum distillation: a batch still for small plants, thin film evaporation (TFE) for continuous plants.
Acid–clay treatment is obsolete. Today base oil is finished by regenerative adsorbent polishing or by hydrofinishing, with no acid sludge and no oily spent clay.
In India used oil is a hazardous waste. A re-refinery needs State Pollution Control Board consent and authorisation and CPCB registration, and it earns EPR certificates under the used oil EPR rules in force since 1 April 2024.
A modular used oil refinery is built as prefabricated, pre-wired skid modules in the factory and arrives ready to install, which makes installation quicker, cheaper and safer than building the plant piece by piece at site.
What is in used engine oil?
In an engine, oil picks up contaminants from combustion, wear and its own ageing:
Water from combustion and condensation, typically 3 to 7 % of collected oil.
Fuel dilution and light hydrocarbons in the petrol and diesel range.
Soot, dust and wear metals such as iron, copper, lead and aluminium.
Spent additives: zinc anti-wear compounds, calcium and magnesium detergents, dispersants and viscosity modifiers.
Oxidation products: organic acids and sludge precursors that darken the oil and give it its smell.
The hydrocarbon molecules of the base oil itself are largely unchanged. That is why re-refining works: take out the contaminants and the oil meets base oil specifications again.

Used engine oil re-refining in six stages, from tanker reception to finished base oil.
Step 1: Testing and reception
Every tanker is sampled before it is unloaded. Quick tests for water, flash point and chlorine, and screening for PCB, protect the plant. Oils containing PCB, chlorinated solvents, brake fluid, glycols, bulk vegetable oils and emulsions are rejected.
Accepted oil is unloaded through a 200 micron duplex strainer into settling tanks, where free water and sludge drop out, and is chemically conditioned at 60 to 80 °C.
Step 2: Dehydration
Water and the lightest hydrocarbons flash off at 110 to 135 °C. Taking water out first prevents foaming and pressure surges in the vacuum section that follows.
Step 3: Light fuel stripping
Next the diesel-range cut, 6 to 12 % of the feed, is separated. In a continuous LINUS plant this light fuel fires the plant's own thermic fluid heater. The heater needs about 40 to 55 litres of fuel per 1,000 litres of feed and the plant recovers 100 to 130 litres, so no fuel is bought after start-up and the surplus is sold.
Step 4: Vacuum distillation
Heavy base oil would have to be heated far above 300 °C to boil at atmospheric pressure, and it would crack. Distilling under deep vacuum lowers the boiling point, so the base oil vaporises without thermal damage and leaves metals, additive residues and asphaltic material behind.
Batch vacuum still
In a batch plant a still is charged with dehydrated oil and heated under a vacuum below 10 mbar. A packed re-refining column with reflux separates a light and a heavy base oil cut, and the batch ends at about 320 °C. Batch stills suit plants up to about 15 TPD: the lowest entry cost, simple operation and tolerance of variable feed.

A 10 TPD modular batch re-refining plant with vacuum still, packed column and polishing columns.
Thin film evaporation
A thin film evaporator spreads the oil as a thin film on a heated wall with a rotating wiper. The oil spends only 10 to 90 seconds on the hot wall, so it does not crack. Two evaporators run in series: TFE-1 at 10 to 30 mbar takes off the light base oil, and TFE-2 at 0.5 to 3 mbar takes the heavy base oil and leaves the asphalt residue. Continuous TFE plants are the better choice from about 20 TPD and give fractionated SN-150 and SN-500 cuts.

A 30 TPD modular continuous re-refinery with thin film evaporators.
Step 5: Finishing the base oil
Distilled base oil still carries colour, odour and polar compounds. How it is finished decides both product quality and the waste the plant produces:
Acid–clay treatment: sulphuric acid, then bleaching clay. Base oil yield is only 50 to 65 %, and it leaves hazardous acid sludge and oily clay. It is banned in many countries.
Clay contacting after distillation: better quality, but it leaves oily spent clay equal to 4 to 7 % of the base oil.
Solvent extraction (NMP, furfural or propane): good Group I quality, but high capital cost, solvent recovery and extract disposal.
Hydrofinishing: hydrogen over a fixed-bed NiMo catalyst at 300 to 340 °C and 45 to 60 bar gives water-white Group II base oil. It pays at large scale.
Regenerative media polishing (LINUS RMP): adsorbent columns at 80 to 100 °C remove colour, odour, organic acids and oxidation products. One column polishes while the other regenerates in place by controlled burn-off at 450 to 550 °C, so there is no spent clay. Media life is 18 to 30 months and finishing typically costs USD 8 to 15 per tonne of base oil.
Step 6: Hydrofinishing for Group II base oil
At 200 TPD, LINUS adds catalytic hydrofinishing after two TFE trains, with a 400 Nm³/h PSA hydrogen unit. The result is API Group II base oil in 70N, 150N, 250N and 500N grades, with VI 100 min and sulphur below 300 ppm, followed by RMP final polishing.

A 200 TPD modular re-refinery with catalytic hydrofinishing for Group II base oil.
What comes out: yields from one tonne of used oil
On specification feed, a LINUS re-refinery typically produces:
Base oil: 68 to 74 % of wet feed, or 72 to 79 % of dry feed (65 % guaranteed).
Light fuel: 6 to 12 %, burned in the plant heater, with the surplus sold.
Asphalt residue: 9 to 17 %, sold as a bitumen extender or heavy fuel.
Water: 3 to 7 %, treated in the effluent treatment plant.
About 98 % of the dry feed leaves the plant as saleable product.
What grade of base oil can you make?
Batch plants: light base oil (SN-150 type, colour L 2.5 max) and heavy base oil (SN-350/500 type, colour L 3.5 max), API Group I.
Continuous TFE plants: SN-150 (colour L 1.5 max) and SN-500 (colour L 2.5 max), VI 95 min, API Group I. A third evaporator adds an SN-300 cut.
Hydrofinishing plants: API Group II 70N, 150N, 250N and 500N, colour L 0.5 max for the light grades.
Batch or continuous: sizing the plant
Size the plant on the used oil you can reliably collect within 300 to 500 km, not on the market for base oil. A 10 TPD plant needs about 3,300 tonnes of used oil a year.
Up to about 15 TPD: batch vacuum distillation (LP-WOD-5B, 10B and 20B).
10 to 100 TPD: continuous two-stage thin film evaporation (LP-WOD-10C to 100C), the usual choice from about 20 TPD.
200 TPD: thin film evaporation with catalytic hydrofinishing for Group II base oil (LP-WOD-200H).
Compare all nine models, with base oil output, plot area and delivery time, on the LP-WOD modular used oil refinery plants page.

A 50 TPD modular continuous used oil refinery with tank farm and heater stack.
Why choose a modular used oil refinery
A conventional re-refinery is built piece by piece at site: steel is erected, equipment is set, and piping, insulation and cabling are fitted in the open over many months. A modular used oil refinery is built the other way round. LINUS supplies every LP-WOD plant as a modular plant: equipment, piping, cable trays, instruments and wiring are installed on structural steel skid modules in our factory and tested before dispatch. At site the modules are set on foundations, bolted together and hooked up.
Prefabricated: equipment, piping, platforms and insulation are assembled on steel skid modules at our Ambernath works, under cover and under our own supervision.
Pre-wired: motors, instruments, cable trays and junction boxes are wired on each module, and every loop is checked before dispatch.
Ready to install: modules arrive numbered with match-marked flanged spools, so site work is limited to setting, bolting up and hook-up.
Faster start-up: modules are built while your civil works proceed, so the plant goes up in weeks instead of months of site construction.
Lower site cost and a safer site: far less site welding, painting, cabling and work at height, which matters next to tank farms and in hazardous areas.
Easy to ship, expand and relocate: modules are sized for road and sea transport, and a thin film evaporator, polishing module or second train can be added later.

A pre-wired modular skid structure with stairs, platforms and columns, assembled and wired before dispatch.
Permits for a used oil re-refinery in India
Used oil is a hazardous waste under the Hazardous and Other Wastes (Management and Transboundary Movement) Rules, 2016. Before it operates, a re-refinery needs:
Consent to establish and consent to operate from the State Pollution Control Board.
Hazardous waste authorisation from the State Pollution Control Board.
Registration as a used oil recycler on the CPCB portal.
Since 1 April 2024, extended producer responsibility (EPR) for used oil makes lubricant producers responsible for having a rising share of their sales recycled: 5 % in 2024-25, rising to 40 % by 2029-30. Registered re-refiners earn EPR certificates for the oil they process, which adds a revenue stream to every litre of base oil.
Planning a modular used oil re-refining plant
LINUS PROJECTS designs and builds turnkey modular used oil refineries from 5 to 200 TPD, prefabricated and pre-wired at its works in Ambernath, near Mumbai. Send your collection volume, the oils you collect, your site location and the base oil grades your market buys, and we will recommend a model with a plot plan and a techno-commercial offer.
Send an enquiry or email sales@linusprojects.com




Comments