top of page
Linus Projects Logo

Coolant and Antifreeze Manufacturing Plant: Process, Raw Materials and Equipment

2 days ago
4 min read

Engine coolant is a blend of glycol, demineralised water and a corrosion-inhibitor package. A coolant manufacturing plant has to do three things well: make clean water, dose every ingredient accurately and fill at speed. LINUS PROJECTS (INDIA) builds coolant and antifreeze plants from 1 to 120 MT per day, alone or combined with a brake fluid plant.

This guide covers the raw materials, the coolant types, the manufacturing process step by step, the equipment, the batch tests and the plant sizes.

Key takeaways

  • Coolant is made by blending mono ethylene glycol (MEG) or mono propylene glycol (MPG) with DM water and inhibitors.

  • The inhibitor package decides the type: IAT, OAT or HOAT.

  • Water quality matters most. The plant needs a DM or RO water plant that delivers below 5 µS/cm.

  • Each batch is tested for freeze point, pH, reserve alkalinity and specific gravity.

  • Coolant is filled by servo gear-pump fillers, then capped, induction sealed, coded and packed.

Raw materials for coolant and antifreeze

  • Glycol: mono ethylene glycol (MEG) for most automotive coolants, or mono propylene glycol (MPG) where lower toxicity is wanted.

  • DM water: demineralised or reverse-osmosis water. Hard or impure water causes scale and corrosion in the engine.

  • Corrosion-inhibitor package: it protects aluminium, cast iron, copper, brass and solder in the cooling system.

  • Dye and antifoam: the dye identifies the coolant type, and the antifoam stops the coolant foaming in the water pump.

Coolant types: IAT, OAT and HOAT

  • IAT (inorganic additive technology): silicate and phosphate inhibitors, the traditional green coolant.

  • OAT (organic acid technology): long-life coolants based on organic acids.

  • HOAT (hybrid OAT): organic acids with a little silicate or phosphate.

Coolant is sold as a concentrate, which the user dilutes, or ready to use. A 50 / 50 mix of MEG and water protects to about −37 °C and raises the boiling point of the cooling system. A mix with one third glycol protects to about −18 °C.

The coolant manufacturing process, step by step

  1. Make DM water. A DM or RO water plant supplies water below 5 µS/cm conductivity.

  2. Take in the glycol. Glycol is pumped from bulk storage, or emptied from drums and IBCs by a decanting unit at up to 2,000 LPH, and dosed through flow meters.

  3. Blend. SS 304 blending vessels with top-entry agitators and recirculation gear pumps mix glycol, water, inhibitors, dye and antifoam. Load cells record the exact batch weight.

  4. Test. The laboratory checks freeze point, pH, reserve alkalinity and specific gravity before the batch is released.

  5. Filter and hold. The approved batch passes a 50-micron basket filter into holding vessels or finished-product tanks.

  6. Fill and seal. Servo gear-pump fillers dose the bottles and cans, followed by capping, induction sealing, inkjet coding and carton taping.

DM water plant with sand filter, cation and anion exchangers for a coolant manufacturing plant

DM water plant for coolant production.

Why a coolant plant needs a DM water plant

Coolant is mostly water, so the water decides how long the coolant protects an engine. Hardness leaves scale on hot surfaces, and dissolved salts attack aluminium and solder. Every LINUS coolant plant therefore includes a DM or RO water plant.

A 1 m³/h DM plant has a multi-grade sand filter, cation and anion exchangers, regeneration tanks and inline conductivity monitoring. It delivers water below 5 µS/cm, with turbidity below 2 NTU and pH 6.5 to 7.5. Large plants use reverse osmosis of up to 5,000 LPH.

Equipment in a coolant manufacturing plant

  • SS 304 blending vessels of 1,000 to 20,000 L with top-entry agitators; large plants put them on load cells

  • SS 304 holding vessels or finished-product tanks

  • Recirculation gear pumps and a 500 LPM water transfer pump

  • A DM or RO water plant, from 1 m³/h to 5,000 LPH

  • A drum / IBC decanting unit and raw-material flow meters

  • A modular platform with stainless steel piping and cast stainless steel valves

  • A PLC + MCC panel with HMI, ready for SCADA

  • A 4-head servo filling machine for 100 ml to 5 L: 32 to 36 bottles per minute at 100 ml and 10 to 12 at 5 L

  • A capping machine, an induction cap sealer for 20 to 100 mm necks, an inkjet coder and a carton taping machine

  • A QC laboratory set

4-head servo filling machine for coolant and antifreeze, 100 ml to 5 litres

4-head servo filling machine for coolant.

Coolant plant sizes

Capacity

Blending vessels

Holding vessels

Water treatment

Filling

2 MT/day

2 × 2,000 L

2 × 5,000 L

DM plant, 1 m³/h

4-head piston and 4-head servo filler

5 MT/day

2 × 5,000 L

2 × 5,000 L

DM plant

4-head piston and 4-head servo filler

10 MT/day

2 × 10,000 L

2 × 10,000 L

DM plant

6-head piston and 6-head servo filler

20 MT/day brake fluid + 20 MT/day coolant

4 × 5,000 L

4 × 5,000 L

DM plant

Matched to pack sizes

120 MT/day coolant

3 × 20,000 L on load cells

Finished-product tanks

RO, 5,000 LPH

High-speed filling lines

Standard configurations for combined brake fluid and coolant plants, and for a 120 MT/day coolant plant. Vessel sizes, filling heads and water treatment are matched to your products and pack sizes.

What moves the price between these sizes is explained in brake fluid and coolant manufacturing plant cost.

Quality control and standards

Before a batch is filled, the laboratory checks freeze point, pH, reserve alkalinity and specific gravity. LINUS plants are designed to make engine coolants that meet ASTM D3306.

Frequently asked questions

Can I make coolant and brake fluid in the same plant?

Yes, as a combined plant. Each product keeps its own vessels and fillers, and the two lines share the DM water plant, the control panel and the laboratory. See the brake fluid manufacturing process.

Which filling machine suits coolant?

Servo gear-pump fillers. One 4-head machine handles packs from 100 ml to 5 L, at 32 to 36 bottles per minute at 100 ml and 10 to 12 at 5 L.

How long does delivery take?

Typically 10 to 16 weeks from order, depending on plant size and the filling line.

Plan your brake fluid or coolant plant

Tell us your products, pack sizes and daily output, and we will send a layout and a budgetary offer. See the brake fluid and coolant plant page, how to start a brake fluid and coolant manufacturing business or contact our sales team (sales@linusprojects.com, +91 98670 80329).

Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
bottom of page

Unit 1 (Registered Office): Plot No. N-86/3, Bohonoli Village, Anand Nagar Additional MIDC, opp. CEAT Tyres, Ambernath (East), Maharashtra 421506, India

Unit 2 (Manufacturing Unit): Plot No. B-73/1, Jhambivali Village, Additional Ambernath MIDC, Ambernath (East), Maharashtra 421506, India